ZIMO S4 Fleet Scooter Error Codes
| Error Code | Description |
|---|---|
0 |
Hardware OK — no fault detected |
301 |
Motor Hall Fault |
302 |
Motor DC current sample Fault |
303 |
Motor 3shunt current sample Fault |
304 |
Overvoltage Fault |
305 |
OverCurrent Fault |
306 |
OverTemp Fault |
307 |
Undervoltage Fault |
308 |
Communication Fault |
309 |
ECU Power on/Power off Fault |
310 |
Motor No Hall Sensor Fault |
311 |
Motor Hall A Sensor Fault |
312 |
Motor Hall B Sensor Fault |
313 |
Motor Hall C Sensor Fault |
314 |
ECU A shunt High Mosfet short circuit |
315 |
ECU A shunt High Mosfet circuit cut off |
316 |
ECU B shunt High Mosfet short circuit |
317 |
ECU B shunt High Mosfet circuit cut off |
318 |
ECU C shunt High Mosfet short circuit |
319 |
ECU C shunt High Mosfet circuit cut off |
320 |
ECU A shunt current sampling Fault |
321 |
ECU B shunt current sampling Fault |
322 |
ECU C shunt current sampling Fault |
323 |
ECU Bus shunt current sampling Fault |
324 |
Motor A shunt cable cut off |
325 |
Motor B shunt cable cut off |
326 |
Motor C shunt cable cut off |
327 |
ECU Over Voltage |
328 |
ECU Under Voltage |
329 |
ECU Mosfet Over temperature |
330 |
ECU Mosfet under temperature |
331 |
ECU Mcu Over temperature |
332 |
ECU Mcu under temperature |
333 |
Motor Over temperature |
334 |
Motor Under temperature |
335 |
ECU Shunt Over current |
336 |
ECU Bus Over current |
337 |
Motor Stall |
338 |
Speed too High |
339 |
Accelerator not under control(Accelerator be press before scooter power on) |
340 |
Main battery Lock Fault |
341 |
Stand sitck sensor Fault |
342 |
Accelerator voltage Low |
343 |
Accelerator voltage High |
344 |
Left Brake voltage Low |
345 |
Left Brake voltage High |
346 |
Right Brake voltage Low |
347 |
Right Brake voltage High |
348 |
Communicate Timeout with IoT |
349 |
Communicate Timeout with ECU |
350 |
Communicate Timeout with BAT |
351 |
Left Brake not under control(Left Brake be press before scooter power on) |
352 |
Right Brake not under control(Right Brake be press before scooter power on) |
601 |
ERROR[601]:ICM sensor init error |
602 |
ERROR[602]:ICM read data error |
603 |
ERROR[603]:sensor reinit |
604 |
ERROR[604]:sensor reinit failed |
605 |
ERROR[605]:BMS communicate Fault |
606 |
Battery off and output alarm |
607 |
Charging |
608 |
over current on charging |
609 |
over current on discharging |
610 |
warning: over voltage |
611 |
Action: over voltage protect |
612 |
warning: under voltage |
613 |
Action: under voltage protect |
614 |
warning: over temp on charging |
615 |
Action: over temp on charging protect |
616 |
warning: under temp on charging |
617 |
Action: under temp on charging protect |
618 |
warning: over temp on discharging |
619 |
Action: over temp on discharging protect |
620 |
warning: under temp on discharging |
621 |
Action: under temp on discharging protect |
638 |
IOT BAT Charging Circuit Fault |
639 |
MCU Fault |
640 |
DataModule Power Fault |
641 |
DataModule Communicate Fault |
642 |
GPS Power Fault |
643 |
GPS Communicate Fault |
644 |
BLE Communicate Fault |
645 |
Sensor Communicate Fault |
646 |
Accelerometer X axis Fault |
647 |
Accelerometer Y axis Fault |
648 |
Accelerometer Z axis Fault |
649 |
Gyroscope X axis Fault |
650 |
Gyroscope Y axis Fault |
651 |
Gyroscope Z axis Fault |
652 |
Display module init Fault |
653 |
Sound module init Fault |
654 |
IoT backup battery Fault |
655 |
IoT backup battery Over temperature |
656 |
Linelock Signal Fault |
657 |
Unauthorised movement |
658 |
Vehicle Fall |
659 |
Main battery Fault |
660 |
Linelock did not plug in |
661 |
IoT over temperature |
662 |
IoT under temperature |
Was this article helpful?
Related Articles
Unlocking the battery compartment lock of the vehicle (Okai / Segway)
If the battery needs to be swapped, what you're going to do is change its status to "charging." This will electronically unlock the battery compartment, allowing you to remove the battery. When the scooter is in the charging state, it will also be taken off the map, so users won't be able to rent…
Replacing the IoT on the Okai ES400 Scooter / Bike
Repair part: IOT Tools list: T20 bit (T20*75mm) Hollow plum blossom bit Electric screwdriver Disassembly steps (Working Hours: 1 minute): Disassemble 2 screws fixing the IOT and remove the IOT. (T20 bit) Disconnect the IOT connector Full parts image: Connect the IOT (green) connector Or…
How does your rental fleet program work?
Levy Fleets is primarily a software and services package that we offer to 3rd party operators looking to launch their own scooter or bike rental fleet. It's primarily geared towards operators running fleets of less than 200 vehicles that don't have the resources to manage their own software, b…